Woodworking Magazine Weblog

I'm curious...on the pictured board would you pare the sawn area to bring it level with the knife line? Or is it good enough as it stands?

Nice example of "witness protection." This same idea is useful when using a plane. A panel gauge will leave these witness marks, handy as you get feather edges when you are close to the marks. Visual yield signs.

-Dean

Did you cut the long tenon shoulders on the front rail in the post below in the same manner?

Do you EVER miss by a hair at some portion of the cut? because if I couldn't do it 100% of the time, I'd rather leave a couple sheets of paper's thickness as insurance. Paring that amount of waste to a knifed line is quick and sure work. Such points may not matter much for dovetails, but do much more so with tenons.

You are a true master.

I can never summon the courage to get that close to my line. I suspect this is because i suck at sawing.

Do you do any sort of warm-up on scrap before you get going on real stock or is sawing like riding a bike for you? Gary Rogowski has mentioned how he does his "5 minute dovetails" at the start of each shop session.

Mike

One other question: I understand that time is money, so colonial cabinet makers and such would certainly want to work from the saw as much as possible (and it shows in many of the antiques I've seen up close where gappy dts are a common sight), but if you are a hobbiest for whom not wasting a rare or expensive board or having flawless visible joinery is more important than a few minutes one way or the other, is there an advantage or reason to aspire to "work from the saw as much as possible"?

Now that you have that macro lens, I have an idea for an article. It might be worthwhile to do some hand tool operations and show what kind of surface is left by the hand tools that still make for good joinery. I know that for me, a big part of the learning curve that I am still getting over is that I see what a tenon made on a tablesaw looks like, and I try to duplicate it with handsaws and chisels, and I'm just learning that such a degree of precision isn't completely necessary.

"I have found that the more you mess with a joint the more likely you will ruin it. The more steps you add to an operation, the more chance that one of them will be faulty."

Can't argue with that, as it's statistically unassailable as a general matter. What it misses, I think, is that it is the relative risk of something going wrong with each particular operation that matters, and not so much the pure number of operations it takes to get to the result. Walking on a diagonal across an intersection comes to mind versus crossing both streets in the cross walk.

In my experience, learning to pare to a line accurately 100% of the time is a more easily attained skill than sawing to the line perfectly 100% of the time.

"So I'll fix the joint if it's open (as noted in the entry). I like tight joints, too."

No doubt, but it's one thing to pare EXTRA from the waste side, and it's another to ADD material back if you stray into the good side. Sometimes it's recoverable - say if the length of the stick between tenon shoulders is not crucial and you can just move the shoulder, but other times it means going to the rack for a new piece of wood. And even if it is recoverable, I dare say the fix will take you far longer than any slight paring would have taken on the front side.

By the way, I worry that it might be hard to tell in written form, but I don't say any of this aggressively or trying to be smart. If we were standing in your shop, woodworker to woodworker, I'd be saying the same stuff and hopefully in a tone that let you know it was just a good nature disagreement on methods (oh so common among us woodworkers, eh?!).

Have a good weekend!

Wait a minute. If you are splitting the knife line, wouldn't the set of the saw teeth obliterate the knife line? Aren't you sawing with the teeth of the saw touching the line rather than splitting the line? Just a matter of semantics; your skill in sawing is evident.

Ken,

One of the benefits of knowing your saw is knowing its set. I position the set of this saw to split the line. I know this sounds all impossible, but it is not (with a little practice).

Chris

I'm new to this is there a place that I can look and start to understand what you are all talking about the line? Thanks Dick.

Dick, I'm not sure I understand your question, but if you are asking about the "line" being referred to in the phrase sawing to the line or plitting the line, we mean literally the line created by the blade of a wheel gauge or a marking knife when marking out the joint to be cut. Some may use pencil lines instead, but the meaning is the same: the mark that dilineates waste from work.

I think you can learn everything need to know about woodworking in 15 minutes,
The rest is practice.
Nice sawing!
Mike

"I know you've heard it a thousand times before. But it's true -- hard work pays off. If you want to be good, you have to practice, practice, practice. If you don't love something, then don't do it."
Ray Bradbury

"In theory there's no difference between theory and practice. In practice there is."
Yogi Berra

"Every day you miss Practicing, it will take you one day longer to get good."
Ben Hogan

It's not practice that makes perfect....but perfect practice that makes perfect.
Cal Ripken Sr.


It's all very well in practice, but it will never work in theory.
French management saying

Chinese jet pilot - Chris you know better - I think you need to be more generic IE jet pilot or neurosurgeon.

John,

It's a line from one of my favorite movies, "Army of Darkness." Not racist. Promise.

Chris

This is a great picture for me to see, as I have wondered if that amount of wood sticking out past the line is a hinderance, i've always pared it off before but now I shall see if I get good results without the paring.
Nathan